| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix tid_tx use-after-free on BA session stop
ieee80211_stop_tx_ba_cb() hands tid_tx to kfree_rcu() through
ieee80211_remove_tid_tx(), and then reads tid_tx->ndp after dropping
sta->lock:
ieee80211_remove_tid_tx(sta, tid); /* kfree_rcu(tid_tx, rcu_head) */
...
spin_unlock_bh(&sta->lock);
if (start_txq)
ieee80211_agg_start_txq(sta, tid, false);
if (send_delba)
ieee80211_send_delba(..., tid_tx->ndp);
That read is not covered by an RCU read-side critical section, and it runs
in preemptible process context: both callers hold the wiphy mutex, reaching
it either from the ieee80211_ba_session_work() wiphy work or from
ieee80211_sta_tear_down_BA_sessions() during station teardown.
Softirqs can run in that window too, both from the local_bh_enable() that
ends ieee80211_agg_start_txq() and from any interrupt exit, so the RCU
callback can free tid_tx before the read.
Driving the function from a test module with the grace period forced into
that window, KASAN reports the read, and the free arrives on the ordinary
RCU softirq path:
BUG: KASAN: slab-use-after-free in ieee80211_stop_tx_ba_cb+0x3cd/0x400
Read of size 1 at addr ffff888002b9f52e by task kworker/0:1/10
[...]
Freed by task 57:
__kasan_slab_free+0x47/0x70
__rcu_free_sheaf_prepare+0x70/0x250
rcu_free_sheaf_nobarn+0x18/0x40
rcu_core+0x426/0x1310
handle_softirqs+0x144/0x590
__irq_exit_rcu+0xea/0x150
irq_exit_rcu+0x9/0x20
sysvec_apic_timer_interrupt+0x6b/0x80
asm_sysvec_apic_timer_interrupt+0x1a/0x20
send_delba is only set when tx_stop is set, which happens for
AGG_STOP_LOCAL_REQUEST alone, so this is reached on local teardown -
session idle timeout, PTK rekey, suspend, HW reconfig - and not from a
peer's DELBA.
Read ndp into a local before the session is freed, while sta->lock is still
held. tid_tx->ndp has a single writer, in
ieee80211_tx_ba_session_handle_start(), which cannot run concurrently here:
both paths are serialised by the wiphy mutex, and the session is already
marked HT_AGG_STATE_STOPPING at this point. tid_tx->ndp is also the only
tid_tx dereference left after ieee80211_remove_tid_tx() in this function.
[move/change the comment a bit to be more general not just on ndp,
initialize ndp directly] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/page_reporting: use system_freezable_wq to fix UAF during suspend
During PM freeze (e.g. S3 suspend or S4 hibernation), device drivers like
virtio_balloon reset their underlying virtio devices and delete their
virtqueues via vdev->config->del_vqs().
However, page reporting work (page_reporting_process) was scheduled on the
global system_wq. Because system_wq lacks the WQ_FREEZABLE flag, the PM
freezer skips it, leaving page_reporting_process active during suspend.
If pages are freed into the buddy allocator while suspending (for example,
when core MM invokes the balloon shrinker during S4 hibernation image
saving), page reporting triggers virtballoon_free_page_report() on deleted
virtqueues, resulting in a Use-After-Free / General Protection Fault:
[ 196.795226] general protection fault, probably for non-canonical address 0xaa1436fe70dae6df: 0000 [#1] SMP NOPTI
[ 196.825967] Workqueue: events page_reporting_process
[ 196.831038] RIP: 0010:virtqueue_add_split+0x233/0x4c0 [virtio_ring]
[ 196.927073] virtballoon_free_page_report+0x3a/0xe0 [virtio_balloon]
[ 196.946943] page_reporting_process+0x370/0x4f0
Fix this by switching page reporting work to system_freezable_wq. This
ensures that the PM freezer pauses page_reporting_process before device
drivers destroy their reporting virtqueues. Because the reporting worker
is frozen, memory reclamation/freeing (e.g. via shrinker execution) can
safely return pages to MM during freeze without triggering unfrozen
reporting work on deleted virtqueues.
This aligns with the driver's existing design. The comment in
virtballoon_freeze() states:
/*
* The workqueue is already frozen by the PM core before this
* function is called.
*/
Testing:
I have verified these fixes using Google’s virtualization infrastructure
by running continuous suspend/resume iterations (40+ cycles) while
churning memory using stress-ng (`stress-ng --vm 4 --vm-bytes 60%
--timeout 1`) to constantly create free pages for the buddy allocator. We
also set the `page_reporting_order` parameter to 0 to make the page
reporting worker highly sensitive, forcing it to pick up any 4K free
pages. This confirmed that the UAF crashes are no longer reproducible. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: stop fast-leave after deleting a port group
br_multicast_leave_group() iterates mp->ports with pp = &p->next in
its fast-leave path. After br_multicast_del_pg() removes p,
continuing the loop advances pp through the deleted entry.
If multicast-to-unicast was enabled, the bridge can hold multiple port
groups for the same port and group with different source MAC
addresses. Once multicast-to-unicast is disabled,
br_port_group_equal() matches those entries by port only. A fast leave
can then delete one entry and continue from its stale next pointer,
leaving mp->ports pointing at a deleted port group.
Fast leave only needs to remove one matching port group. Break after
br_multicast_del_pg() so the loop stops before dereferencing the
removed entry. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Check return value of __register_event() in trace_module_add_events()
trace_module_add_events() ignores the return value of __register_event()
and unconditionally calls __add_event_to_tracers() for each event.
If __register_event() fails (for example, if event_init() fails), the
trace_event_call is not added to ftrace_events list, but
__add_event_to_tracers() still creates a trace_event_file pointing to it.
If module loading subsequently fails and module memory is freed, tracing
state retains a stale trace_event_call pointer in trace_event_file,
leading to a use-after-free when tracefs or tracing subsystem operations
are later executed.
Fix this by checking the return value of __register_event() and only
calling __add_event_to_tracers() if event registration succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix potential UAF on meter attach failure
While attaching a newly created meter attach_meter() function makes
the new meter visible to other CPUs but can still fail afterwards.
On failure, it detaches the meter back and returns an error.
However, this is an unexpected behavior for the ovs_meter_cmd_set()
that uses a plain kfree(meter) on attach failure without waiting for
RCU readers to stop using it, assuming it was never visible.
This is never a problem for ovs-vswitchd as it always creates meters
before creating any flows that use them. But the UAF can be triggered
with a custom application using uAPI:
BUG: KASAN: slab-use-after-free in ovs_meter_execute (net/openvswitch/meter.c:653)
Read of size 8 at addr ffff88810d152650 by task meter/2508
Call Trace:
ovs_meter_execute (net/openvswitch/meter.c:653)
do_execute_actions (net/openvswitch/actions.c:1407)
ovs_execute_actions (net/openvswitch/actions.c:1584)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:703)
...
netlink_sendmsg (af_netlink.c:1900)
Allocated by task 2519:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
ovs_meter_cmd_set (net/openvswitch/meter.c:422)
...
netlink_sendmsg (af_netlink.c:1900)
Freed by task 2519:
kfree (mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720)
ovs_meter_cmd_set (net/openvswitch/meter.c:479)
...
netlink_sendmsg (af_netlink.c:1900)
Fix that by making sure attach_meter() doesn't make the meter visible
until all the checks are done and the function can't fail anymore.
This also makes sure the "hash" value is calculated after the potential
re-sizing of the table.
Reported by Trend Micro's Zero Day Initiative as ZDI-CAN-31642. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: fix pptable use-after-free
amdgpu_dpm_get_pp_table() returns a pointer to a driver-owned power table
after dropping adev->pm.mutex. The sysfs path then copies from that pointer.
A concurrent pp_table write can replace and free the allocation during the
copy, causing a use-after-free.
Change the DPM interface to copy into caller-provided storage while the mutex
is held. Keep the size-only query for attribute discovery without exposing
the driver-owned pointer.
(cherry picked from commit f6eed7acfd30099ef7baeb6ba45bb59daad80631) |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: serialize kernel accept preallocation with socket teardown
rxrpc_kernel_charge_accept() reads rx->backlog without any
socket/backlog synchronization and passes that raw pointer into
rxrpc_service_prealloc_one(). A concurrent rxrpc_discard_prealloc()
sets rx->backlog = NULL and frees the backlog rings, so a kernel
preallocation worker can keep using a freed struct rxrpc_backlog
while updating *_backlog_head/tail and array slots.
Serialize the state check and backlog lookup with the socket lock,
and reject kernel preallocation once teardown has disabled
listening or discarded the service backlog. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Fix RB-tree corruption in probe error path
The info->node RB-tree member is zero-initialized via kzalloc. If
a device does not support ATS, the device_rbtree_insert() call is
skipped. If a subsequent probe step fails, the error path jumps to
device_rbtree_remove(), which misinterprets the zeroed node as
a tree root and corrupts the device RB-tree.
Fix this by explicitly initializing the RB-node as empty using
RB_CLEAR_NODE() during initialization and guarding the removal with
RB_EMPTY_NODE(). |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: Fix possible use after free
In dma_release_channel(), check chan->device->privatecnt after call
dma_chan_put(). However, dma_chan_put() call dma_device_put() which could
release the last reference of the device if the DMA provider is already
gone and hence free it.
Fixes it by moving dma_chan_put() after the check. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: make sure gc is properly stopped
Sashiko noticed that when destroying a set,
cancel_delayed_work_sync() was called while gc
calls queue_delayed_work() unconditionally which
can lead not to properly shutting down the gc. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: stp: Fix a potential use-after-free when deleting a bridge
The three STP timers are not supposed to be armed while the bridge is
administratively down. They are synchronously deactivated when the
bridge is put administratively down and the various call sites check for
'IFF_UP' before arming them.
This check is missing from br_topology_change_detection() and it is
possible to engineer a situation in which the topology change timer is
armed while the bridge is administratively down, resulting in a
use-after-free [1] when the bridge is deleted.
Fix by adding the missing check and for good measures synchronously
shutdown the three timers when the bridge is deleted.
[1]
ODEBUG: free active (active state 0) object: ffff88811662b9b0 object type: timer_list hint: br_topology_change_timer_expired (net/bridge/br_stp_timer.c:120)
WARNING: lib/debugobjects.c:629 at debug_print_object+0x1bc/0x450, CPU#9: ip/359 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix HV VHCA stats agent registration race
mlx5e_hv_vhca_stats_create() registers the stats agent through
mlx5_hv_vhca_agent_create(). The helper publishes the agent in
hv_vhca->agents[type] under agents_lock and immediately schedules an
asynchronous control invalidation on the HV VHCA workqueue before
returning to mlx5e.
The asynchronous invalidation invokes the control agent's invalidate
callback, which reads the hypervisor control block and forwards the
command to mlx5e_hv_vhca_stats_control(). That callback may either:
- call cancel_delayed_work_sync(&priv->stats_agent.work), or
- call queue_delayed_work(priv->wq, &sagent->work, sagent->delay).
However, the delayed_work and priv->stats_agent.agent are only
initialized after mlx5_hv_vhca_agent_create() returns to mlx5e:
agent = mlx5_hv_vhca_agent_create(...); /* publish + invalidate */
...
priv->stats_agent.agent = agent; /* too late */
INIT_DELAYED_WORK(&priv->stats_agent.work, ...); /* too late */
If the asynchronous control path runs before the two assignments
above, it can:
- Operate on an uninitialized delayed_work whose timer.function is
NULL. queue_delayed_work() calls add_timer() unconditionally, so
when the timer expires the timer softirq invokes a NULL function
pointer.
- Re-initialize the timer later through INIT_DELAYED_WORK() while
the timer is already enqueued in the timer wheel, corrupting the
hlist (entry.pprev cleared while the previous bucket node still
points at this entry).
- When the worker eventually runs, mlx5e_hv_vhca_stats_work() reads
sagent->agent (NULL) and dereferences it inside
mlx5_hv_vhca_agent_write().
Fix this by:
- Initializing priv->stats_agent.work before invoking
mlx5_hv_vhca_agent_create(), so the work is always in a valid
state when the control callback observes it.
- Adding a struct mlx5_hv_vhca_agent **ctx_update out-parameter
to mlx5_hv_vhca_agent_create(). The helper writes the agent
pointer to *ctx_update before publishing into hv_vhca->agents[]
and triggering the agents_update flow, so any callback
subsequently invoked from that flow already sees a valid
priv->stats_agent.agent. This avoids having the control
callback participate in agent initialization.
While at it, access priv->stats_agent.agent with
READ_ONCE()/WRITE_ONCE() for the cross-CPU access with the worker, and
clear priv->stats_agent.buf on the agent_create() failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: Fix adv monitor add failure cleanup
hci_add_adv_monitor() publishes a new adv_monitor in
hdev->adv_monitors_idr before the powered MSFT setup step. The MSFT
offload add path can then fail either locally before the controller add
command completes, or in the MSFT add callback. In the current queued
management add flow, hci_cmd_sync_work() still invokes
mgmt_add_adv_patterns_monitor_complete() with the original pending command
after msft_add_monitor_pattern() returns.
The buggy scenario involves two paths, with each column showing the order
within that path:
MSFT add handling MGMT completion
1. insert monitor and handle 1. receive sync error
2. send MSFT add command 2. call add-monitor completion
3. callback sees bad response 3. load cmd->user_data
4. callback frees monitor 4. read monitor->handle
Local MSFT setup failures have the other half of the same ownership bug:
they return an error after the IDR insertion, but no later code removes the
failed monitor from the IDR.
Keep ownership with the pending management command until its completion.
For normal management adds, the MSFT add callback now records successful
controller state and returns errors to its caller. The management
completion frees the monitor on non-success after copying the response
handle, while resume/reregister callback-error cleanup remains in the
MSFT callback. The success path keeps the existing bookkeeping.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x5f0
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x19f/0x330
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
kasan_report+0xe0/0x110
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
? 0xffffffffc00d00da
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
? hci_cmd_sync_work+0x1ab/0x210 [bluetooth]
hci_cmd_sync_work+0x1c0/0x210 [bluetooth]
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
process_one_work+0x4fd/0xbc0
? __pfx_process_one_work+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? __list_add_valid_or_report+0x37/0xf0
? __pfx_hci_cmd_sync_work+0x10/0x10 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
worker_thread+0x2d8/0x570
? __pfx_worker_thread+0x10/0x10
kthread+0x1ad/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c9/0x540
? __pfx_ret_from_fork+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? __switch_to+0x2e9/0x730
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 471 on cpu 3 at 285.205389s:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
__kasan_kmalloc+0xaa/0xb0
add_adv_patterns_monitor_rssi+0xd5/0x230 [bluetooth]
hci_sock_sendmsg+0x96b/0xf80 [bluetooth]
__sys_sendto+0x2bc/0x2d0
__x64_sys_sendto+0x76/0x90
do_syscall_64+0x115/0x6a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 454 on cpu 2 at 285.217112s:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x5f/0x80
kfree+0x313/0x590
msft_add_monitor_sync+0x54a/0x570 [bluetooth]
hci_add_adv_monitor+0x133/0x180 [bluetooth]
hci_cmd_sync_work+0x187/0x210 [bluetooth]
process_one_work+0x4fd/0xbc0
worker_thread+0x2d8/0x570
kthread+0x1ad/0x1f0
ret_from_fork+0x3c9/0x540
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_queue: pin bridge device while NFQUEUE holds fake dst
The br_netfilter fake rtable is embedded in struct net_bridge and is
attached to bridged packets with skb_dst_set_noref(). If such a packet is
queued to NFQUEUE, __nf_queue() upgrades that fake dst with
skb_dst_force().
At that point the queued skb can hold a real dst reference after bridge
teardown has started. The problem is not that every bridged packet needs
its own dst reference. The problem is that NFQUEUE can keep the bridge
private fake dst alive after unregister begins.
Fix this by keeping the bridge fake dst model unchanged and pinning the
bridge master device only while the packet sits in NFQUEUE. Record the
bridge device in nf_queue_entry when the queued skb carries a bridge fake
dst, take a device reference for the queue lifetime, and drop it when the
queue entry is freed.
Also make sure queued entries are reaped when that bridge device goes
down, and drop the redundant nf_bridge_info_exists() test from the fake
dst detection.
This keeps netdev_priv(br->dev) alive until verdict completion, so the
embedded fake rtable and its metrics backing storage cannot be freed out
from under dst_release(). It also avoids the constant refcount bump and
avoids using ipv4-specific dst helpers for IPv6 bridge traffic. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_nat_sip: reload possible stale data pointer
quoting sashiko:
------------------------------------------------------------------------
[..] noticed a potential memory bug and header corruption involving the
SIP NAT helper.
In net/netfilter/nf_nat_sip.c:nf_nat_sip():
if (skb_ensure_writable(skb, skb->len)) {
nf_ct_helper_log(skb, ct, "cannot mangle packet");
return NF_DROP;
}
uh = (void *)skb->data + protoff;
uh->dest = ct_sip_info->forced_dport;
if (!nf_nat_mangle_udp_packet(skb, ct, ctinfo, protoff,
0, 0, NULL, 0)) {
If a cloned or fragmented SKB is reallocated by skb_ensure_writable(), the
old data buffer is freed. However, nf_nat_sip() fails to update *dptr to
point to the new buffer.
It also appears to use nf_nat_mangle_udp_packet() on what could be a TCP
packet, which would overwrite the sequence number with a checksum update.
------------------------------------------------------------------------
nf_conntrack_sip linerizes skbs, hence no fragmented skb can be seen.
But clones are possible, so rebuild dptr.
Disable nf_nat_mangle_udp_packet() branch for TCP streams.
It doesn't look like this can ever happen, else we should have received
bug reports about this, so just check the conntrack is UDP and drop
otherwise.
The calling conntrack_sip set ->forced_dport for SIP_HDR_VIA_UDP messages,
so I don't think this is ever expected to be true for a TCP stream. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_reasm: guard mac_header adjustment after IPv6 defrag
nf_ct_frag6_reasm() slides the packet head forward to drop the IPv6
fragment header and then unconditionally advances skb->mac_header:
skb->mac_header += sizeof(struct frag_hdr);
On the NF_INET_LOCAL_OUT defrag path the skb has no link-layer header
yet, so skb->mac_header is still the "not set" sentinel (u16)~0U. Adding
sizeof(struct frag_hdr) wraps it to a small value (0xffff + 8 == 7),
after which skb_mac_header_was_set() wrongly reports a MAC header is
present and skb_mac_header() points into the headroom.
The reassembler has done this unconditional add since it was introduced;
it was harmless while mac_header was a bare pointer, but wrong once
mac_header became a u16 offset whose unset state is the ~0U sentinel
tested by skb_mac_header_was_set(). The sibling net/ipv6/reassembly.c
does the same relocation and does guard the adjustment; mirror the
guard here. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: retrieve ethhdr after potential skb realloc on RX
pskb_may_pull() in batadv_interface_rx() could reallocate the buffer behind
the skb. Variables which were pointing to the old buffer need to be
reassigned to avoid an use-after-free.
This was done correctly for the VLAN header but missed for the ethernet
header which is later used for the TT and AP isolation handling. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: pin svc_xprt across the asynchronous TLS handshake callback
svc_tcp_handshake() stores the raw svc_xprt pointer in
tls_handshake_args.ta_data and submits the request through
tls_server_hello_x509(). The handshake core takes only
sock_hold(req->hr_sk); nothing references the embedding struct
svc_sock that svc_tcp_handshake_done() reaches via container_of().
Two close races leave the in-flight callback writing through a freed
svc_sock. svc_sock_free() calls tls_handshake_cancel() and discards
its return value: a false return means handshake_complete() has
already set HANDSHAKE_F_REQ_COMPLETED but hp_done() may not have
finished, yet svc_sock_free() proceeds to kfree(svsk). The
cancel-loser fall-through inside svc_tcp_handshake() itself produces
the same window: when wait_for_completion_interruptible_timeout()
returns <= 0 (timeout or signal) and tls_handshake_cancel() returns
false, the function does not drain, returns, and svc_handle_xprt()
calls svc_xprt_received(), which clears XPT_BUSY and can drop the
last reference. A concurrent close then runs svc_sock_free() while
svc_tcp_handshake_done() is still updating xpt_flags and walking
svsk->sk_handshake_done.
The corruption surfaces as set_bit/clear_bit RMW into the freed
xpt_flags slab slot and as complete_all() walking and writing the
freed wait_queue_head_t list embedded in sk_handshake_done -- a
slab-corruption primitive, not a benign read. The path is reachable
on any TLS-enabled NFS server whenever a connection close overlaps
the tlshd downcall delivery window; the interruptible wait means
signal delivery suffices, not just SVC_HANDSHAKE_TO expiry.
Take svc_xprt_get(xprt) immediately before tls_server_hello_x509()
so the in-flight callback owns its own reference. Release it on the
two edges where the callback is guaranteed not to fire -- submission
failure from tls_server_hello_x509() and a successful
tls_handshake_cancel() -- and at the tail of
svc_tcp_handshake_done() after complete_all().
[cel: rewrote commit message to describe the actual change] |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: fix use-after-free race with concurrent NETDEV_UNREGISTER
isotp_release() looked up the bound network device via dev_get_by_index()
using the stored ifindex. During device unregistration the device is
unlisted from the ifindex hash before the NETDEV_UNREGISTER notifier
chain runs, so a concurrent isotp_release() could find no device, skip
can_rx_unregister() entirely, and still proceed to free the socket.
Since isotp_release() had already removed itself from the isotp
notifier list at that point, isotp_notify() would never get a chance to
clean up either, leaving a stale CAN filter that keeps pointing at the
freed socket.
Fix this the same way raw.c already does: hold a tracked reference to
the bound net_device in the socket (so->dev/so->dev_tracker) from
bind() onward instead of re-resolving it from the ifindex, and
serialize bind()/release() with rtnl_lock() so that so->dev is always
consistent with what the NETDEV_UNREGISTER notifier sees. so->dev
stays valid regardless of ifindex-hash unlisting, and is only ever
cleared by whichever of isotp_release()/isotp_notify() gets there
first, so the filter is always removed exactly once.
isotp_bind() now rejects a (re)bind with -EAGAIN while so->[tx|rx].state
isn't ISOTP_IDLE yet, so a timer left running by a prior
NETDEV_UNREGISTER can't act on a newly bound so->ifindex. Both checks
share the same lock_sock() section, so there is no window in which a
concurrent isotp_notify() clearing so->bound could be missed. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing rcu list annotations and operations
sashiko-bot remarked the missing use of list_add_rcu() in
bcm_[rx|tx]_setup() to have a proper initialized bcm_op structure
when bcm_proc_show() traverses the bcm_op's under rcu_read_lock().
To cover all initial settings of the bcm_op's the list_add_rcu() calls
are moved to the end of the setup code.
While at it, also fix the mirroring removal side: bcm_release() called
bcm_remove_op() - which frees the op via call_rcu() - on ops that were
still linked in bo->tx_ops/bo->rx_ops, without list_del_rcu() first.
Unlink each op with list_del_rcu() before handing it to bcm_remove_op(),
matching the existing pattern in bcm_delete_tx_op()/bcm_delete_rx_op(). |
